*This is a buisness line and does not accept text messages.

Millennium CNG Conversion Kit for 4, 6, 8 or 10 Cylinder Fuel Injected Engines

Model CNGM4 $379

Model CNGM6 $399

Model CNGM8 $449

This kit is universal and works on 8 or 10 cylinder gasoline fuel injected engines up to 8 liters, non turbo, non GDI.

Our Owners Manual provides detailed instructions, wiring diagrams and a complete trouble guide. It is only available with a kit purchase.

Please completely read all the information below before ordering.

We will need the following information about your vehicle when ordering a conversion kit:

1. Fill Nozzle Type (Read Fill Nozzle Options section below.)

2. Mixer Size (Measure you air intake hose near the throttle body where the mixer will be installed and select the largest mixer that will fit inside the air intake.

3. Year of Vehicle

4. Make of Vehicle

5. Model of Vehicle

6. Number of Cylinders

7. Engine Size in Liters

8. Comments (Leave any additional information or comments you may have.)

There are a few gasoline engines that may require special parts from us or after market parts. They are listed below.

1. Engines with dual air intake hoses may require a dual mixer kit.

The dual mixer kit comes with an additional mixer, a tee fitting, 18" of additional hose, and 4 additional hose clamps.

1. Many OBDII engines will require an injector emulator.

2. Works best with older fuel injected engines approximately model years 2004 and older or out of useful life condition for miles and model year.

Fill Nozzle Options

We have two fill nozzle options.

1. Standard fill nozzle with 1/4 turn shutoff valve with 2 ports so it can be installed in-line from the cylinder to the regulator. This is what you should order unless you need one of the other options.

2. Strait nozzle without shutoff valve. For installing in tight or hard to get to locations. Comes with an extra 1/2 length roll of tubing. It is connected directly to the tank valve. The regulator is connected directly to the other port of the tank valve.

Stainless Steel Fittings Option

For a small additional cost we can supply 1/4" or 3/8" stainless steel fittings so you can install stainless steel tubing instead of the steel tubing that comes with our kits. We do not supply the stainless steel tubing. We recommend our steel tubing as it is lower in cost and much easier to install. Call to order if desired.

Listed Below are Just a Few Features of the Millennium Conversion Kit.

1. Automatic conversion to gasoline before you run out of CNG.

2. Smooth instant automatic conversion to CNG while starting on gasoline. The conversion RPM and fuel overlap are adjustable using the software to provide the smoothest and safest conversion.

3. Option to always start on CNG.

4. Adjustable mixer available in 5 sizes 2, 2.5, 3, 3.5, and 4 inch diameters.

5. Easier fuel injector wiring with many fuel injector connector types available.

6. All computer controlled solid state electronics.

7. No fuel injector emulators to wire and install.

8. Emergency CNG starting and operation if the engine will not operate on gasoline.

9. Has Oxygen Sensor diagnostics to warn you of any operating problems.

10. Comes with software instructions, a USB computer cable and software.

11. Comes with installation and operating instructions with many tips, how to information, and a trouble guide.

12. Many other features and adjustments available using the software gives a high degree of tunability.

Our Millennium conversion kit is universal for non-GDI and naturally aspirated fuel injected engines.

All of our kits have a control on the dash which indicates which fuel you are using and how much CNG is in your tank.

All of our kits allow you to run on either gasoline or CNG with the push of a button on the dash.

All of our kits come with regulators designed for your engine size for more power and better performance.

Our Millennium kit will automatically switch to gasoline if you run out of CNG. You should always refuel before you run out of either fuel.

We have kits for every engine

We have conversion kits for most gasoline engines and a low cost kit for diesel engines.

We design all of our kits ourselves, and we manufacturer some of the parts. Some of our parts are imported from other countries. Some parts are built in the USA.

We have chosen the best parts with the best prices to provide the best kits available at the best price.

All our kits are rated for 3,600 psi and come complete with everything you need including the filling nozzle. CNG storage tanks, tank valves, and mounting brackets are sold separately. You can use any type of CNG tanks with our kits.